EcoSoya PB Instructions EcoSoya Piller Blend (PB) is self-releasing so it is perfect for all molded candles: pillars, votives, tarts, novelty candles, etc. Molds Molds should be clean and room temperature. Conditioning is recommended with new molds or molds previously used with paraffin. This simply involves thoroughly wiping the inside walls with warm soybean/vegetable oil. Dyes Most dyes (powder, liquid, chips, blocks, etc.) work with PB. To achieve better color depth, use about 30% more dye. When using powder dyes, heat the wax to 190°F (87.8°C), add the dye, and mix until dissolved. Powder dyes may also be dissolved in fragrances and then added to the melted wax (be sure the dye has dissolved completely before adding). *When using powder dyes dissolved in fragrance, liquid dyes, color blocks, chips or no dye, heat the was to 155°F (68.3°C). Fragrance Many fragrances work in PB, especially those designed for soy wax in general. Recommended maximum scent load is about 12%. To minimize scent loss, add scent prior to pouring but at a wax temperature no less then 145°F (61.1°C). Accomodate for temperature drop due to the addition of the cooler scent when targeting pour temperature. Some scents may react poorly causing bleed, objectionable frosting, or poor flame quality. Try a different scent or manufacturer to correct that occurrence. Wicking PB requires larger wicking than paraffin. Wicks such as paper cored, cotton cored or metal cored should be avoided as they tend to cause sooting and carbon build-up. PB tends to burn more down than out creating a Hurricane Candle effect in pillar candles. Scent, color and candle configuraton have a great impact on the best wick choice. Too large of a wick may cause sooting, quick burn times and guttering (wax leaking through the side of the candle).MeltingWhen using dye, except for powdered or un-dyed PB, melt the wax to a minimum of 155°F (68.3°C) under gentle agitation to promote even heating and thorough mixing. For powder dyes, heat the wax to 190°F (87.8°C) to ensure the dye dissolves. Temporary high temperatures such as 190°F (87.8°C) have no adverse effect if cooled quickly. Higher temperatures, in excess of 190°F (87.8°C) may cause wax to discolor. Allow the wax to cool to the desired pour temperature.PouringIt is typical for wax to solidify at the beginning of the pour during its first contact with the mold. PB should have a pour temperature high enough so that when the mold is full, the initial solidified wax has remelted. The temperature should not be so high that the liquid wax sits more than 30 minutes before starting to solidify.Pour temperatures will vary according to mold type and size, fragrance and dye, and the effects preferred. PB does not normally produce static electricity or bubbles when poured, tapping of the molds is not necessary. A recommended starting temperature is 155°F (68.3°C).There is a difference in cooling rates for different mold configurations. Cooling too quickly or too slowly can cause cracking and/or frosting. If difficulties are experienced with your pour temperatures, try a lower or higher temperature in increments of 10°F (6°C).PB Double-Pour: When using EcoSoya PB two pours are required with candles such as 3 & 4 inch (7.6 cm & 10.2 cm) diameter pillars. The first pour is done at 155°F (68.3°C) by filling the mold to the top and allowing the candle to set up with a warm but congealed soft center. If the top of the mold (bottom of the candle) has "skinned" over and left a void inside, poke two holes into the candle near the wick.The second pour is done at 140°F (60.0°C) while the candle center is still warm but congealed.Do not pour past the solidified wax of the first pour; in essence "fill" the first pour.Making Votives with PB: The first pour is done at 155°F (68.3°C) by filling the mold within 1/8 inch (0.3 cm) from the top. Allow the votive to cool until it is still warm with a congealed center that has no liquid. If the top of the candle has "skinned" over, poke two holes near the wick. Pour a second time at 140°F (60.0°C) to completely fill the votive mold.Pour temperatures should be checked and confirmed according to seasonal changes.Candle Cooling and Mold ReleaseCool undisturbed candles at an ambient temperature of 70°F (21.1°C). The molds should be at least 1/2 inch (1.3 cm) apart to allow air circulation for even cooling.EcoSoya PB is self-releasing. Slower cooling will encourage the candle to adhere to the mold causing it not to release, while quicker cooling will encourage pull away and release. PB is designed to shrink back from the mold for easier release and should be encouraged to do so. Silicone mold release spray may be used in the unusual event of poor release.Candles should be allowed to sit undisturbed for 48 hours before test burning.