Lietuviška versija  English version
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Sale

Height 5.3cm Height 5.3cm...detail
3.99 €   2.49 €         
Height 5.3cm Height 5.3cm...detail
3.99 €   2.49 €         
 
KeraSoy Container Wax<p>KeraSoy Container Wax is a blend specifically developed for the production of container candles. It is suitable for further blending with fragrances and oil soluble dyestuffs. KeraSoy Container blend is biodegradable and vegan friendly. No animal products are used and no animal testing has been carried out in its manufacture. KeraSoy Container Wax does not require additives, other than fragrance and colour required by the Candle maker. Old or partial candles may be remelted and the wax reused although it is advisable not to heat the wax above 85°C or heating for extended lengths of time. Waxes should be stored in a cool, dry location away from direct heat, sunlight and moisture.<br />Containers</p><p>Containers should be clean and free of contaminants. Containers should be at least at room temperature, although pre-heating the containers to approx. 45 - 50°C can be beneficial.<br />Colour</p><p>Most dyes work with KeraSoy Container; powder, liquid, chips, blocks, etc. When using powder dyes, heat the wax to approx. 75°C, add the dye and mix until dissolved. Powder dyes may also be dissolved in fragrance and then added to the melted wax, be sure the dye has dissolved completely before adding. When using powder dyes dissolved in fragrance, liquid dyes, colour blocks, chips or no dye heat the wax to 70°C. If you wish to make your candle darker or "richer", add a little black dye to the colour you are using.<br />Fragrance</p><p>KeraSoy Container may be used with fragrance at levels up to 10-12%, however fragrance which is specifically developed for use with natural waxes is highly recommended. Burn pool size and depth greatly affect fragrance throw so correct wicking is paramount. Some fragrances may react poorly with the wax causing bleeding, objectionable surface finishes or poor flame quality. This has been found to be exaggerated when using fragrances specifically designed for use in Paraffin wax candles.<br />Wicking</p><p>Natural waxes tend to require larger wick sizes than traditional paraffin waxes. Fragrance, colour and candle configuration have a great impact on the best wick choice. Too large of a wick may cause sooting, accelerated burn times and guttering (wax leaking through the side of the candle). Too small a wick will cause tunnelling and produce a smaller flame. Keep wicks trimmed to ¼ inch. If you experience poor flame quality or stability, try a different type of wick. Test burning should be done after the candle has had a chance to sit for 48 hours after pouring.<br />Melting</p><p>Temporary high temperatures (up to 90°C) have no adverse effect as long as the wax is cooled back down quickly. Higher temperatures may cause the wax to discolour. Allow the wax to cool to your desired pour temperature, add the fragrance and mix well. Be sure to stir/mix the wax while melting. Avoid using containers containing copper and zinc as this may accelerate discolouration. Stainless Steel is the material of choice although mild steel is acceptable. Digital temperature probes are readily available and are a safer choice than the traditional Mercury in glass type.<br />Pouring</p><p>Pour temperatures may vary according to mould type & size, fragrance & dye used and the effects the candle maker wishes to achieve. Greater adhesion to containers can be achieved by pouring at temperature close to congealing point (approximately 45 - 55°C). Fragrance should be added and mixed immediately prior to pouring where practical. If you experience difficulties with your pour temperature, try a lower or higher temperature in increments of 5 - 10°C. Consider pouring into pre heated moulds for better adhesion to glass containers.<br />Double-Pour</p><p>KeraSoy Container is formulated to require only a single pour in most containers however, for some large containers; a top-up is required to achieve the best candle surface. A small amount of wax at a slightly warmer temperature than the candle was poured at can be used to top-up the candle before the candle is fully cool (pouring the top-up once the candle is completely cool may result in a reduction of adhesion to the container).<br />Candle Cooling</p><p>Cool undisturbed candles at room temperature (about 25°C). Candles should be allowed to sit undisturbed for 48 hours before test burning.</p> KeraSoy Container Wax

KeraSoy Container Wax is a blend specifically developed for the production o...detail

4.45 €   3.99 €         
Size: 10x9cm Size: 10x9cm...detail
11.95 €   9.99 €         
 
KeraSoy Pillar Blend<p>KeraSoy Pillar Blend is a blend specifically developed for the production of Pillar candles and wax tarts. It is suitable for further blending with fragrances and oil soluble dyestuffs. Kerasoy Pillar blend is biodegradable and vegan friendly. No animal products are used and no animal testing has been carried out in its manufacture. KeraSoy Pillar Blend does not require additives, other than fragrance and colour required by the Candle maker. Old or partial candles may be remelted and the wax reused but it is advisable not to heat the wax above 85°C or heating for extended lengths of time. Waxes should be stored in a cool, dry location away from direct heat, sunlight and moisture.<br />Moulds</p><p>Moulds should be clean and free of contaminants. They should be at least at room temperature, although pre-heating to approx. 45 - 50°C can be beneficial.<br />Colour</p><p>Most dyes work with KeraSoy Pillar; powder, liquid, chips, blocks, etc. When using powder dyes, heat the wax to approx. 75°C, add the dye and mix until dissolved. Powder dyes may also be dissolved in fragrance and then added to the melted wax, be sure that the dye has dissolved completely before adding. When using powder dyes dissolved in fragrance, liquid dyes, or colour blocks heat the wax to 70°C. If you wish to make your candle darker or "richer", add a little black dye to the colour you are using.<br />Fragrance</p><p>KeraSoy Pillar has been designed for fragrance at levels between 5 - 10%. Fragrance which is specifically developed for use with natural waxes is highly recommended. Burn pool size and depth greatly affect fragrance throw so correct wicking is paramount. Some fragrances may react poorly with the wax causing bleeding, objectionable surface finishes or poor flame quality. This has been found to be exaggerated when using fragrances specifically designed for use in Paraffin wax candles.<br />Wicking</p><p>Natural waxes tend to require larger wick sizes than traditional paraffin waxes. Fragrance, colour and candle configuration have a great impact on the best wick choice. Too large of a wick may cause sooting, accelerated burn times and guttering (wax leaking through the side of the candle). Too small a wick will cause tunneling and produce a smaller flame. Keep wicks trimmed to ¼ inch. If you experience poor flame quality or stability, try a different type of wick. Test burning should be done after the candle has had a chance to sit for 48 hours after pouring.<br />Melting</p><p>Temporary high temperatures (up to 90°C) have no adverse effect as long as the wax is cooled back down quickly. Higher temperatures may cause the wax to discolour. Allow the wax to cool to your desired pour temperature, add the fragrance and mix well. Be sure to stir/mix the wax while melting. Avoid using Pillars containing copper and zinc as this may accelerate discolouration. Stainless Steel is the material of choice although mild steel is acceptable. Digital temperature probes are readily available and are a safer choice than the traditional Mercury in glass type.<br />Pouring</p><p>Pour temperatures may vary according to mould type & size, fragrance & dye used and the effects the candle maker wishes to achieve. Greater release from the moulds may be achieved by pouring at temperature of around 55 - 65°C, although this will be dependent upon the size and shape of the candle being produced. Fragrance should be added and mixed immediately prior to pouring where practical. If you experience difficulties with your pour temperature, try a lower or higher temperature in increments of 5 - 10°C. Consider pouring into pre heated moulds for enhanced release properties.<br />Double-Pour</p><p>KeraSoy Pillar is formulated to require only a single pour, however for some large Pillars; a top-up is required to achieve the best candle surface. A small amount of wax at a slightly warmer temperature than the candle was poured at can be used to top-up the candle before the candle is fully cool (pouring the top-up once the candle is completely cool may result in a reduction of adhesion to the Pillar).<br />Candle Cooling</p><p>Cool undisturbed candles at room temperature (about 25°C). Candles should be allowed to sit undisturbed for 48 hours before test burning. Test Burn: Check wicking. Test burn the candle for burn pool diameter and "mushrooming" after it has cooled for 48 hours. Mushrooming is when carbon and/or other substances build up on the end of the wick interfering with combustion. Mushrooming can cause sooting and poor odours. Try different wicks until you have your desired burn pool diameter and a good clean flame.  </p> KeraSoy Pillar Blend

KeraSoy Pillar Blend is a blend specifically developed for the production of ...detail

4.19 €   3.99 €         
Size: 24.5x30cm. 30 Pages Size: 24.5x30cm. 30 Pages...detail
19.49 €   13.99 €         
 
sheet 50x70 cm, 19 g<p>Thin, semi-transparent tissue paper great for decorating, wrapping and crafts</p> sheet 50x70 cm, 19 g

Thin, semi-transparent tissue paper great for decorating, wrapping and crafts...detail

2.99 €   2.49 €         
QUALITY : Water based colours, vivid and intense for painting on silk. Fluid, they fuse on silk. COLOUR COLOUR MIXABILITY : can be mixed together DRYING : air dry in a few minutes SURFACES: all types of silk THINNER : Setasilk thinner OPACITY : Transparent colours FINISH : Brilliant TO FIX: Press on the reverse side of the fabric for 5 minutes using an iron set on the “cotton” position. CARING: (decorated fabrics) : 48 hours after fixing, colours resist handwashing and dry cleaning BRUSHES : Soft and very thin, with a high retention capacity, the pure squirrel brushes are ideal for painting on silk. From a modern technology, the Aqua range brushes are made from synthetic fibres, are soft and durable, can match the performance of sable at the best price. For backgorunds and washes, foam brushes are the most practical. BRUSH CLEANING : Soapy water QUALITY : Water based colours, vivid and intense for painting on silk. Fluid, they fuse on silk. COL...detail
3.15 €   2.99 €         
 
QUALITY : Water based colours, vivid and intense for painting on silk. Fluid, they fuse on silk. COLOUR COLOUR MIXABILITY : can be mixed together DRYING : air dry in a few minutes SURFACES: all types of silk THINNER : Setasilk thinner OPACITY : Transparent colours FINISH : Brilliant TO FIX: Press on the reverse side of the fabric for 5 minutes using an iron set on the “cotton” position. CARING: (decorated fabrics) : 48 hours after fixing, colours resist handwashing and dry cleaning BRUSHES : Soft and very thin, with a high retention capacity, the pure squirrel brushes are ideal for painting on silk. From a modern technology, the Aqua range brushes are made from synthetic fibres, are soft and durable, can match the performance of sable at the best price. For backgorunds and washes, foam brushes are the most practical. BRUSH CLEANING : Soapy water QUALITY : Water based colours, vivid and intense for painting on silk. Fluid, they fuse on silk. COL...detail
3.15 €   2.99 €         
QUALITY : Water based colours, vivid and intense for painting on silk. Fluid, they fuse on silk. COLOUR COLOUR MIXABILITY : can be mixed together DRYING : air dry in a few minutes SURFACES: all types of silk THINNER : Setasilk thinner OPACITY : Transparent colours FINISH : Brilliant TO FIX: Press on the reverse side of the fabric for 5 minutes using an iron set on the “cotton” position. CARING: (decorated fabrics) : 48 hours after fixing, colours resist handwashing and dry cleaning BRUSHES : Soft and very thin, with a high retention capacity, the pure squirrel brushes are ideal for painting on silk. From a modern technology, the Aqua range brushes are made from synthetic fibres, are soft and durable, can match the performance of sable at the best price. For backgorunds and washes, foam brushes are the most practical. BRUSH CLEANING : Soapy water QUALITY : Water based colours, vivid and intense for painting on silk. Fluid, they fuse on silk. COL...detail
3.15 €   2.99 €         
 
The setaskrib air dry in 30 minutes; <br />they are then fixed using an iron (cotton position), pressing for 2 to 3 minutes on the reverse side of the decorated fabric;<p>May be applied on all pre-washed fabrics;<br />Hour after fixing, the decorated fabrics are resistant to washing at 40-degree C.</p> The setaskrib air dry in 30 minutes;
they are then fixed using an iron (cotton position), pres...detail
2.90 €   2.49 €         
The setaskrib air dry in 30 minutes; <br />they are then fixed using an iron (cotton position), pressing for 2 to 3 minutes on the reverse side of the decorated fabric;<p>May be applied on all pre-washed fabrics;<br />Hour after fixing, the decorated fabrics are resistant to washing at 40-degree C.</p> The setaskrib air dry in 30 minutes;
they are then fixed using an iron (cotton position), pres...detail
2.90 €   2.49 €         
 
The setaskrib air dry in 30 minutes; <br />they are then fixed using an iron (cotton position), pressing for 2 to 3 minutes on the reverse side of the decorated fabric;<p>May be applied on all pre-washed fabrics;<br />Hour after fixing, the decorated fabrics are resistant to washing at 40-degree C.</p> The setaskrib air dry in 30 minutes;
they are then fixed using an iron (cotton position), pres...detail
2.90 €   2.49 €         
...detail
3.35 €   2.49 €         
 
Diameter 12cm Diameter 12cm...detail
0.80 €   0.59 €         
400pcs. 400pcs....detail
0.81 €   0.59 €         
 
Size: 10x15.5cm Size: 10x15.5cm...detail
1.00 €   0.79 €         
Size: 25x3.7cm Size: 25x3.7cm...detail
2.49 €   1.49 €         
 
Water based ink, ready to use. High pigment concentration. Inter-mixable colours. Apply on watercolour paper, drawing paper, boards, etc. Can be diluted with distilled water for lighter colours. Clean the equipment with water. Water based ink, ready to use. High pigment concentration. Inter-mixable colours. Apply on watercolo...detail
3.42 €   1.99 €         
Water based ink, ready to use. High pigment concentration. Inter-mixable colours. Apply on watercolour paper, drawing paper, boards, etc. Can be diluted with distilled water for lighter colours. Clean the equipment with water. Water based ink, ready to use. High pigment concentration. Inter-mixable colours. Apply on watercolo...detail
3.42 €   1.99 €         
 



Pages: 1   2   3   4  
Goods in cart: 0
Total: 0.00 €
 
 
                                    
© 2010 - 2024 DEKONAMAI